Williams Sound DLT 100 2.0 Bedienungsanleitung Seite 11
- Seite / 32
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver
11
Address Conrmation
Press the MENU button twice for the CM and CS, once for SLVs. The address for the DLT 100 2.0 will be displayed for two
seconds.
NOTE: Every DLT 100 2.0 MUST have its own address and all must be assigned to the same group.
Quick Group Change
“Groups” apply to 2-way Mode only.
1. With the DLT 100 2.0 powered ON, push and hold the Group button
until the GROUP indicator on the
screen starts blinking and the light above the Group button comes on (Figure 5).
2. Change groups by pushing the Up button
or the Down button . If no buttons are pushed, the
Quick Group Change feature will time out after 5 seconds.
3. Push the Group button
once to exit the Quick Group Change function, or wait for 5 seconds.
Push-to-Talk (Ptt) and Push-and-Latch (PNL)
This feature allows the user to choose between Push and Latch (PnL) or Push to Talk (Ptt). The default is PnL.
In PnL mode, when the TALK button
is pressed and released, it stays in talk mode until the TALK button is
pressed and released again.
In Ptt mode, the TALK button must be held down while speaking, and when released, it shuts o.
The DLT 100 2.0 must be set up as a Slave unit, in 2-way mode, prior to performing these steps.
1. With the DLT 100 2.0 powered ON, press and hold the Up button
and the Down button
simultaneously for 2 seconds to enter programming mode.
2. Push the Power/Menu button until the TALK indicator is ashing and either “PnL” is or “Ptt” is displayed.
(Figure 6).
3. Use either of the -/+ buttons
to switch between “PnL” and “Ptt”
4. Press and hold the Up button
and the Down button simultaneously for 2 seconds to exit
programming mode.
Side Tone Adjustment
This gives the user the ability to change the volume of their own voice heard in the headset (side tone).
1. With the DLT 100 2.0 powered ON, press and hold the Up button
and the Down button
simultaneously for 2 seconds to enter programming mode.
2. Push the Power/Menu button until “St:” is displayed. See Figure 7.
3. Use either of the -/+ buttons
to choose between Stt:0 (O), St:1 (-6dB) (default), or St:2 (-12dB).
4. Press and hold the Up button
and the Down button simultaneously for 2 seconds to exit
programming mode.
Talk “O” Double-Beep Indication Limit
The user hears an audible “double-beep” sound when the TALK button is turned o. This is heard in the headset of the user only; it
is not transmitted. On the DLT 100 2.0, as the headset volume is increased, the beep volume will increase until the headset volume
reaches 37, then the beep volume will stop increasing. (Note: On the DLT 100 the beep volume continued to get louder as the
headphone volume was increased, with no limit.)
A474
FIGURE 5
A473
FIGURE 6
A472
FIGURE 7
- Digi-Wave 1
- Digi-Wave™ 2
- CAUTION! 3
- System Overview 4
- Step 1. Set Mode: 2-way 8
- Step 3. Set Address 8
- Step 4. Set Group Number 8
- Step 1. Set Mode: 1-way 9
- Step 3. Set Channel 9
- Secure Key Code: 10
- SET-Up Lock (SLOC) 10
- Attendee Checking 10
- Tone Control 10
- Address Conrmation 11
- Quick Group Change 11
- Side Tone Adjustment 11
- DLT 100 2.0 Operation 12
- MICROPHONE LEVEL ADJUSTMENT 13
- TALK BUTTON 13
- DLR 60 2.0 Controls 14
- DLR 60 2.0 Operation 14
- HOW IT WORKS 15
- HOW IT WORKS (CONTINUED) 16
- 2-Way Receive Only 17
- 2-Way (i.e. Tour Guide) 17
- Repeater 20
- Receive Only 20
- Speak Only (Main Speaker) 20
- Receive/Speak (Interpreter) 20
- IMPORTANT 21
- Repeater Mode 22
- ^ button / yes “ch+” button 23
- (slave units only) 24
- Specications 25
- Troubleshooting 27
- FCC statements 29
- 2-year Warranty 30
- MAN 153G 32
Verwandte Produkte und Handbücher für Empfänger Williams Sound DLT 100 2.0
(4 Seiten)Kärcher Special machinery user manuals
Starting on N
Kommentare zu diesen Handbüchern